ASTM B26 PDF

Aluminum Alloys. Refer to ASTM Specification B26/B26M Chemical Compostion (%Max, unless range is stated). Others. ANSI Alloy #. UNS. Si. Fe. Cu. Mn. ASTM B26/B26M: Standard Specification for Aluminum-Alloy Sand Castings. ASTM B26/B26M Standard Specification for Aluminum-Alloy Sand Castings. standard by ASTM International, 05/15/ This document has been replaced.

Author: Mikataur JoJorn
Country: Benin
Language: English (Spanish)
Genre: Sex
Published (Last): 6 August 2016
Pages: 75
PDF File Size: 17.65 Mb
ePub File Size: 4.16 Mb
ISBN: 788-6-24165-750-8
Downloads: 93525
Price: Free* [*Free Regsitration Required]
Uploader: Tygora

Addition of small amounts of modifiers and grain refining elements to the molten alloys from the remelting furnace is permitted before casting. A Contains silver 0. It may not address the mechanical properties, integrity testing, and verification required for highly loaded or safety critical applications.

ASTM B26 / B26M – 12 Standard Specification for Aluminum-Alloy Sand Castings

ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date. B If iron exceeds 0. It is informational only and not an official part of the standard; the full text of the standard itself must be h26 to for its use and application. This specification covers aluminum alloy sand castings except those that are for aerospace applications.

ASTM-BB26M ADOPTION NOTICE ALUMINUM ALLOY SAND CASTINGS

C Contains beryllium 0. Note 3—The following applies to all specified limits in this table: Note 2—Analysis shall ashm made for the elements for which limits are shown in this table.

  DISTILLATION DESIGN KISTER PDF

Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of adtm other.

Combining values from the two systems may result in nonconformance with the standard.

Link to Active This link will always route to the current Active version of the standard. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Historical Version s – view previous versions of standard. Note 1—When single units are shown, these indicate the maximum amounts permitted.

This abstract is a brief summary of the referenced standard. Active view current version of standard.

ASTM-B26/B26M, ADOPTION NOTICE: ALUMINUM ALLOY SAND CASTINGS (15-MAY-1992) [SUPERSEDING QQ-A-601F]

Pure metals, recycled materials, and master alloys can also be used to make the alloys as long as the chemical composition can be analyzed and adjusted to conform to the requirements prior to pouring any casting. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other.

  DELMORE SCHWARTZ IN DREAMS BEGIN RESPONSIBILITIES PDF

Combining aatm from the two systems may result in nonconformance with the standard. Link to Active This link will always route to the current Active version of the standard.

b266 It may not address the mechanical properties, integrity testing, and verification required for highly loaded or safety critical applications. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. The chemical compositions are determined in accordance with the specified suitable chemical and spectrochemical test methods.

For purposes of determining conformance to these limits, an observed value or a calculated value obtained from analysis shall be rounded to the nearest unit in the last right-hand place of figures used in expressing the specified limit in accordance with the rounding method of Practice E Castings should only be repaired using approved processes such as welding, impregnation, peening, blending, soldering, and so forth.

Unified Numbering System alloy designations are in accordance with Practice E