The CVQ valve is operated by the EKC controller. Please notice that a power failure will cause the CVQ pilot valve to fully open ICS / PM. If it is required that. Type Code, EKC Weight, Kg. Approval, CE, C-TICK, EAC, LLC CDC TYSK. Data comm. options, LON RS EAN no. Freq. View and Download Danfoss EKC user manual online. Controller for regulation of media temperature. EKC Controller pdf manual download.
|Published (Last):||8 June 2012|
|PDF File Size:||13.27 Mb|
|ePub File Size:||17.44 Mb|
|Price:||Free* [*Free Regsitration Required]|
The service menu of the electronic controller is of particular interest to the fitter upon commissioning or servicing of the plant.
Danfoss EKC 361 User Manual
S according to entered setpoint. The controller is operated using two push buttons. The first option is the fastest possible refrigeration. Special attention must be paid to the start-up phase of regulation. The lowest occurring suction pressure will have a belonging t value which in turn indicates the value of the n02 setting. 36 13 If the actual application has a requirement re- garding max.
The “NTC” resistor sends the control confirmation of the degree of opening of the valve via the inner actuator temperature. Danfoss reserves the right to alter its products without notice. Add to my manuals Add.
In the case of this setting, a very clear undershooting of the outlet temperature of the evaporator is to be expected to facilitate fast refrigeration danfosw ensure the reference temperature is quickly achieved. In the case of a media temperature control for refrigerating plants with a pipe size of up to 54 mm, an electrically controlled valve e. The “EKC ” control has three different transient processes available.
Service The service menu of the electronic controller is of particular interest to the fitter upon commissioning or servicing of the plant. Eck is possible to equip the control with a LON module and record the appropriate data using a master unit and to intervene in the control system remotely using a modem connection.
EKC – Documents
Operation The controller is operated using two push buttons. Page 16 Danfoss can accept danfosa responsibility for possible errors in catalogues, brochures and other printed material.
The second option only allows slight undershooting. Controller for operation of evaporator on water chiller 16 pages. In the case of electric defrosting, the “KVS” is opened. Don’t have an account? Solution for large plants If connection sizes larger than 54 mm are required for the suction line, it is recommended that you implement a solution with a main valve. These values provide information about the state of the plant.
Due to tolerances in the actuator, the setting value must be 10 K lower than shown in the curve. In applications such as this, constant nozzle air temperature from evaporators is the key to success. The actual value of this actuator temperature and the current reference value can be read in the control menu of “EKC ” “”. This can be done using special software type “Danfoss AKM”.
However, applications in the food industry are also possible. The “KVS” is a continuous valve with which even the smallest fluctuations in evaporation pressure can be avoided.
Here it is important to eliminate danofss the smallest temperature changes so that the measuring results are not affected. Continuous electronic valves The “KVS” is a continuous valve with which even skc smallest fluctuations in evaporation pressure can be avoided. If the actual application has a requirement re- garding max.
B – Product specifications
Either can be necessary. Remote service is also possible for this control system. The controller can be completely programmed using these two buttons combined with a danfosa display where all important data is displayed. The last option is to completely eliminate outlet values below the reference value during the start-up phase.
The individual status codes have the following meanings: However, with “CVQ” an actuator is used to operate the valve instead of a stepper motor. On the one hand, they can be read quickly, which saves the effort of measuring with the temperature gauge. Due to tolerances in the actuator the value must be set 10K lower than indicated in the curves on page This is an advantage, particularly where the release of high pressure and, if necessary, liquid in the evaporator are concerned.
Enter text from picture: