LA3600 DATASHEET PDF

LA datasheet, LA circuit, LA data sheet: SANYO – 5-Band Graphic Equalizer,alldatasheet, datasheet, Datasheet search site for Electronic. LA datasheet LA component LA integrated circuit LA schematic LA application note A LA LA36 LA3. Sanyo LA datasheet, 5-Band Graphic Equalizer (1-page), LA datasheet, LA pdf, LA datasheet pdf, LA pinouts.

Author: Visar Zulkihn
Country: Cayman Islands
Language: English (Spanish)
Genre: Life
Published (Last): 4 January 2012
Pages: 210
PDF File Size: 20.18 Mb
ePub File Size: 15.56 Mb
ISBN: 489-8-41999-289-3
Downloads: 14285
Price: Free* [*Free Regsitration Required]
Uploader: Tagore

Most of the IC manufacturers call their multi band tone controls as graphic equalisers.

(Datasheet) LA pdf – 5-Band Graphic Equalizer (1-page)

Previous post Next post. Assemble the circuit on a good quality PCB.

Could i add this to my homemade tube amp, and take out the LA? LA is a single integrated single Op-amp, 5 band graphic equalizer IC which is very suitable for applications like portable stereo, radio sets, home theater systems, car audio systems etc.

Capacitors C2, C4, C6, C8, C10 and C15 are the input capacitors and increasing the value of these capacitors will increase the low frequency response. I used 9V DC for powering the circuit.

How we connect stereo input to this circuit? If you use slider potentiometers as controls and mount them vertically in a sequence from left to right as R1 to R5 and as you slide it down, should cut the frequency spectrum for which it is meant and sliding up should boost. Laa3600 email address datasheft not be published. The LA can be operated from anything between 5 to 15V DC and is extremely stable to capacitive loads. satasheet

  CTHULHUTECH BURNING HORIZON PDF

Datasheet «LA3600»

This will hold good only when following are carried out. The LA can be operated from anything between 5 to 15V DC and is extremely stable to capacitive loads.

If you use slider potentiometers as controls and mount them vertically in a sequence from left to right as R1 to R5 and as you slide it down, should cut the frequency spectrum for which it is meant and sliding up should boost. LA is a single integrated single Op-amp, 5 band graphic equalizer IC which is very suitable for applications like portable stereo, radio sets, home theater systems, car audio systems etc. C12 is the output capacitor and resistor R6 limits the supply current.

I used 9V DC for powering the circuit. Then the contour of the knobs represents the frequency response of the tone control unit. In the circuit capacitors C1, C3, C5, C7 and C9 are used to fix the resonance frequency of the corresponding bands. Hi Eric Nice question.

5-band Graphic Equalizer

Most of the IC manufacturers call their multi band tone controls as graphic equalisers. In the circuit capacitors C1, C3, C5, C7 and C9 are used to fix the resonance frequency of the corresponding bands.

C12 is the output capacitor and resistor R6 limits the supply current. Your email address will not be published. This will hold good only when following ratasheet carried out.

  DYREKTYWA 90 496 EWG PDF

LA Datasheet –

You may also like: Assemble the circuit on a good quality PCB. Capacitor C13 is a decoupling capacitor and C14 is a power supply filter circuit. The power supply must be well regulated and noise free. Then the contour of the knobs represents the frequency response of the laa3600 control unit.

Leave a Reply Cancel reply Your email address will not be published. Previous post Next post. You may also like: Could i add this to my homemade tube amp, and take out the LA? Leave a Reply Cancel reply Your datawheet address will not be published.

Capacitors C2, C4, C6, C8, C10 and C15 are the input capacitors and increasing the value of these capacitors will increase the low frequency response. Capacitor C13 is a decoupling capacitor and C14 is a power supply filter circuit.

Gain of each band can be adjusted by using the corresponding potentiometers R1 to R5. The power supply must be well regulated and noise free. Hi Eric Nice question. Gain of each band can be adjusted datashfet using the corresponding potentiometers R1 to R5. How we connect stereo input to this circuit?