AMSCM 5A Low Dropout Voltage Regulator FEATURES. Three Terminal Adjustable or Fixed V, V and V Output Current of 5A Operates Down to. the end of the datasheet. Typical Application. 1. An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in. The AIC is a low dropout three terminal regulator with 5A output current capability. The output voltage is adjustable with the use of a resistor divider or fixed.

Author: Gardasho Gugal
Country: Lesotho
Language: English (Spanish)
Genre: Automotive
Published (Last): 28 October 2008
Pages: 253
PDF File Size: 17.84 Mb
ePub File Size: 13.19 Mb
ISBN: 317-5-60893-624-2
Downloads: 83505
Price: Free* [*Free Regsitration Required]
Uploader: Mejind

Load and line regulation are measured at constant junction temperature, and are guaranteed up to the maximum power dissipation of 30W.

Aic 1084cm pdf

The reason for the 2 diodes was to protect against high input voltages because I believed that if we exceeded the 1.

The higher the thermal resistance, the hotter the IC. I recently got into the quadcopter hobby and purchased a UDI UA mini quadcopte r from Ebay which is fun to fly and have been experimenting changing the battery packs and adding FPV. Therefore a 5V adjustment decreases ripple rejection by a factor of four dB ; Output ripple increases as adjustment voltage increases.

After purchasing 4 micro motors Hubsan X4 Ha set of propellers to suit, a MPU 3 axis accelerometer and gyro, I was ready to start building. OldFashioned Ice Cream Maker. Heat dissipation is predictable by knowing the thermal resistance between the IC and ambient?


CE – – IC Chips – Kynix Semiconductor

All numbers apply for packages soldered directly into a PC board. One big downside is that acrylic is heavy compared to most other materials. The LM is guaranteed to provide a minimum dropout voltage 1. Power dissipation is kept in a safe range by current limiting circuitry.

But, if the output is shorted, then the recovery involves a large input to output differential. Datashee is desirable to have large output capacitance for applications that entail large changes in load current microprocessors for example. I x ESR It is common practice to use several tantalum and ceramic capacitors in parallel to reduce this change in the output voltage by reducing the overall ESR.

Aic cm pdf In order for stable operation, the loop must maintain negative feedback. Life support devices or systems are devices or systems which, I are intended for surgical implant into the body or ii support or sustain life, and whose failure.


See Ripple Rejection section regarding the value for the adjust pin capacitor. The maximum power dissipation is a function of TJ max ,?

But since it is small uA maxfatasheet becomes negligible when R1 is in the Ohm range. The fixed versions intergrate the adjust resistors. Given a collection of models for the data, AIC estimates the quality of each model, relative to each of the other models. JA max is calculated as: I’m learning about electronics bit by bit, making projects and tearing things apart.


【CM AMS】Electronic Components In Stock Suppliers in 【Price】【цена】【Datasheet PDF】USA

The junction temperature can be predicted as follows: Refer to curve section for the short circuit current vs. PCB date code is 4th week of The equivalent series resistance ESR of solid tantalum or aluminum electrolytic capacitors is used to provide the appropriate zero approximately kHz.

Posted in Teardowns on Jun 10th, If I were to re-do this project I would have laid out the PCBs better so they could just connect to each other without wires. Typical Application using Fixed Output Regulator When the adjustable regulator is used Figure 4the best performance is obtained with the positive side of the resistor R1 tied directly to the output terminal of the regulator rather than near the load.

PCB date code is July to March CH If thermal compound is used,? Refer to short circuit curve in the curve section. Under these conditions it may be necessary to recycle the power of the regulator in order to get the smaller differential voltage and thus adequate start up conditions.