3G3EV OMRON PDF

This OMRON 3G3EV-ABMA-CUE SYSDRIVE Inverter is used and in excellent condition. Configurations: A: Panel Mounting Installation Type B. Omron SYSDRIVE 3G3EV SERIES Pdf User Manuals. View online or download Omron SYSDRIVE 3G3EV SERIES User Manual. View and Download Omron SYSDRIVE 3G3EV user manual online. Compact Low-noise Inverter. SYSDRIVE 3G3EV Inverter pdf manual download.

Author: Vudojinn Vudodal
Country: Mauritania
Language: English (Spanish)
Genre: Video
Published (Last): 8 August 2011
Pages: 442
PDF File Size: 15.50 Mb
ePub File Size: 1.36 Mb
ISBN: 685-5-81478-257-4
Downloads: 44860
Price: Free* [*Free Regsitration Required]
Uploader: Kazizahn

Separate Input and Output Terminal Blocks Power input terminals are located in the upper section, while motor output terminals are in the lower section. Never Short or Ground the Output Terminals Caution If the output terminals are touched with bare hands or the output wires come into contact with the Inverter casing, an electric shock or grounding will occur.

Omron SYSDRIVE 3G3EV SERIES Manuals

Modify the sequence so that brakes are applied when the Inverter enters DC braking status. Stopped item indicators red indicators These items can be set only when the Inverter is stopped.

S When the connector comes off, grip the lower edges of the Digital Operator, and slide it down ormon it comes off. Chapter 7 Gearmotor The speed range for continuous omton differs according to the lubrication method and motor manufacturer. Chapter 4 Preparing for Operation 6. Page 38 Chapter 4 Function of Each Component Display Sections Data display section Reference frequency values, output frequency values, output current values, constant settings, and error codes are displayed.

For the 3-wire sequence, refer to the wiring on page Note that this warning is applicable whenever you perform any task after turning the main circuit off.

Electromagnetic waves from the 3ge3v and cables cause the broadcasting radio receiver to make noise. Inverter monitors over-torque only selection when speed is matched.

However, motor vibration may become greater in the following cases: Touching terminals while the main circuit is on may cause an electrical shock and dam- age the equipment. Digital Operator Chapter 2 Overview H Digital Operator Data display section Monitor item indicators In-service item indicators green indicators Display These items can be monitored or set even section during operation.

  FORMULASI SAMPO PDF

Any intellectual property in the Products is the exclu Omroh use and handling of the product will ensure proper product performance, will length product life, and may prevent possible accidents. Eliminating the cause recovers the system automatically. Frequency detection output frequency Thank you for submitting your InstraView Request! How to Prevent Induction Noise As described above, a noise filter can be used to prevent induction noise from being generated okron the output side. Chapter 3 Design D Wires to be Used Always use twisted-pair shielded wires to kmron malfunctions due to noise.

Electromagnetic waves from the Inverter and cables cause the broadcasting radio receiver to make noise. Although care has been given in documenting the product, please contact your OMRON representative if you have any suggestions omroon improving this manual. Operation in progress 2: To prevent this, adjust the carrier frequency set in n37 as shown in the table below. Chapter 3 If the cable is long and may cause voltage drops, increase the wire omrron according to the cable length.

OMRON 3G3EV-AM-CE – In Stock, We Buy Sell Repair, Price Quote

Amperage input DIP switch 5. We know there are plenty of differences when it comes to used equipment and quite often, choosing between different pieces is difficult, especially when the equipment is not sitting right in front of you. If voltage is applied to the output terminals, the internal mechanism of the Inverter will be damaged.

Page 35 Chapter 4 Preparing for Operation H Function of Each Component D Display Sections Data display section Reference frequency values, output frequency values, output current values, constant settings, and error codes are displayed.

Items to be Checked when Unpacking Chapter 4 Frequency Detection Level Setting range 0.

  INTRODUCTION TO MODERN LINGUISTICS MOHA ENNAJI PDF

Wire type Wire size Wire to be used Single wire 0. Connect the Inverter to power supply and peripheral devices.

Omron SYSDRIVE 3G3EV SERIES User Manual

Chapter 7 Appendix A 3. Page 87 Chapter 7 Gearmotor The speed range for continuous ojron differs according to the lubrication method and motor manufacturer. Page 56 Chapter 4 Error code Description Error category n50 is used to specify whether over-torque is to be monitored and specify the action to be taken when over-torque is detected.

Set the word address in constant no.

Chapter 5 Maintenance and Inspection Daily Inspection While the system is operating, check the following items: The data display section also flashes. The constants for basic operations are allocated to dedicated indicators, so the user need not refer to the constant nos.

Chapter 4 Preparing for Operation H Monitor Display The 3G3EV allows the user to monitor the reference frequency, output fre- quency, output current, and the direction of rotation. All constants can be set. Got it, continue to print. D How to Prevent Induction Noise As described above, a noise filter can be used to prevent induction noise from being generated on the output side. The RUN and ALARM indicators on the front panel indicate the current Inverter sta- tus, and the data display section also displays information about an error that has occurred.

Do not connect a positive terminal to a negative terminal. Page 46 Chapter 4 Preparing for Operation Note MA is turned on when the difference between the reference frequency and the output frequency falls within 2 Hz. In addition, cooling effects also decline in the low-speed range, resulting in an increase in the motor temperature.

Table of Contents Add to my manuals Add. Same as for n06 input selection 3