ACT4060 DATASHEET PDF

ACT datasheet, ACT circuit, ACT data sheet: ACTIVE-SEMI – Wide Input 2A Step Down Converter,alldatasheet, datasheet, Datasheet search site. ACT Datasheet PDF Download – Wide Input 2A Step Down Converter, ACT data sheet. Active-Semi ACT datasheet, Wide Input 2A Step Down Converter (1-page), ACT datasheet, ACT pdf, ACT datasheet pdf, ACT pinouts.

Author: Maulrajas Zulkill
Country: Chad
Language: English (Spanish)
Genre: Relationship
Published (Last): 27 September 2010
Pages: 42
PDF File Size: 3.27 Mb
ePub File Size: 19.46 Mb
ISBN: 160-8-66856-593-2
Downloads: 36978
Price: Free* [*Free Regsitration Required]
Uploader: Zolokazahn

Bypass this pin to G with a low ESR capacitor. Therefore, a lower capacitance value can be used for ceramic capacitors.

When EN is less than 0. So don’t give up. Output Voltage Setting Figure 3 shows the connections for setting the output voltage. However, if FB voltage is less than 0. Finally, select the inductor core size so that it does not saturate at 3A. F SP Cap 15k?

The Oscillator normally switches at kHz. When I tried to replace inductor to 10uH It was a little bit better but the problem still existed. How can the power consumption for computing be reduced for energy harvesting?

This is wasting our time.

ACT 데이터시트(PDF) – Active-Semi, Inc

See Input Capacitor in the Application Information section. The voltage at this pin is regulated to 1.

  HARRY MULISCH THE ASSAULT PDF

When left unconnected, EN is pulled up to 4. There is a problem when writing a datasheet. Users should evaluate each product to make sure that dataheet is suitable for their applications. I’m convinced that incorrect or lack of compensation contributes to this a lot, but no doubt I’m wrong, ‘though compensation is a must-have for regulated outputs. The inductance for example: Current limit happens when COMP reaches its maximum clamp value of 2. PV charger battery circuit 4. Datasehet course everything is soldered on PCB.

The Oscillator normally switches at kHz. This inductor current has a ripple that is dependent on the inductance value: Note that EN is a low voltage input with a maximum voltage of 6V; it should never be directly connected to IN.

See Stability Compensation in the Application Information section. Current limit happens ddatasheet COMP reaches its maximum clamp value of 2.

The input capacitance needs to be higher than 10? I will replace ac4t060 inductor and let know the results. Input port and input output ddatasheet declaration in top module 2. At this point, the SW side of the inductor swings to a diode voltage below ground, causing the inductor current to decrease and magnetic energy to be transferred to output. CMOS Technology file 1. I must say, breadboards are eerie places with phantom frequencies appearing all over the place, like an echo chamber, not good to begin with.

  CRYSOMALLON SQUAMIFERUM PDF

This inductor current has a ripple that is dependent on the inductance value: Distorted Sine output from Transformer 8. I redesigned power supply module and put it on separate PCB, and now It seems that everything work without any problems. Protection features include cycle-by-cycle current limit, acf4060 shutdown, and frequency foldback at short circuit.

The output ripple voltage is: PNP transistor not working 2. When lower than 0. Digital multimeter appears to have measured voltages lower than expected.

ACT4060 PDF Datasheet浏览和下载

Choosing IC with EN signal 2. Make sure that this peak inductor current is less that the 3A current limit.

Turn on power triac – proposed circuit analysis 0. We all needed to go through it. When I open the datasheet, then there is a complete chapter called ” Inductor xct4060.

Part and Inventory Search. In the case of tantalum or electrolytic capacitors, the ripple is dominated by RESR multiplied by the ripple current. Therefore, a lower capacitance value can be used for ceramic type.