ASTM D 3299 PDF

Buy ASTM D REDLINE Standard Specification for Filament-Wound Glass-Fiber-Reinforced Thermoset Resin Corrosion-Resistant Tanks from SAI. Dec 2, One of the most com- monly used specifications for filament- wound FRP tanks is ASTM D This standard was first published in and. For Filament Wound Fabrications: ASTM D Specification for Filament Wound Glass. Fiber Reinforced Thermoset Resin Chemical Resistant Tanks.

Author: Mooguran Gohn
Country: Colombia
Language: English (Spanish)
Genre: Business
Published (Last): 4 July 2007
Pages: 354
PDF File Size: 5.56 Mb
ePub File Size: 6.68 Mb
ISBN: 379-4-80363-742-3
Downloads: 75088
Price: Free* [*Free Regsitration Required]
Uploader: Tetaxe

Tolerances on installation are shown in Fig.

Never set a tank upon a? The shell taper shall not exceed 1? It is the responsibility of the fabricator, using a thixotropic agent in the resin required for 7. When the qstm laminate consists only of a corrosion barrier, the length of the laminate, hr shall be a minimum of 3 in. Glass content of this?

Resources & News

NOTE 12—Support of auxiliary equipment, snow load, or operation personnel 32999 require additional reinforcement or the use of stiffener ribs, sandwich construction, or other stiffening systems. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

In addition, this clearance shall not be less than the shear distance required for proper installation of the nozzle see 7.

Surfaces shall be clean and dry before lay-up. NOTE 8—The use of an accepted analytical technique, such as laminated plate theory LPTfor design and analysis of composite vessels may predict stresses, strains, and strength on a ply-by-ply basis, given some basic lamina properties.

  DISEO DE PERSONAJES CHRIS PATMORE PDF

Dimensions and Tolerances 8. If damage has occurred, a claim should be? If additional longitudinal strength is required, the use of other reinforcements, such as woven fabric, nonwoven astn or bidirectional fabric, chopped-strand mat, or chopped strands, may ast interspersed in the winding to provide additional strength.

ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up aetm date. Current edition approved March 10, Suitable methods include use of ultraviolet absorbers, incorporation of pigment of sufficient opacity in the outer surface resin-rich layer, or use of resins inherently resistant to ultraviolet aetm. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

NOTE 2—Gaskets shall be 1?

The Design Tanks Difference: Exceeding The Standards | Design Tanks

Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm. Prior to hoisting the top end, a suitable protection pad of material should be placed under the bottom pivot point of tank so that as the tank rises, the strain is taken on the pad. Methods of manufacture that incorporate stiffening bands as a means of knuckle stabilization, are permissible alternatives by agreement between purchaser and fabricator, provided the fabricator can document the validity of the design.

  IL PRINCIPE PIERO MELOGRANI PDF

NOTE 15—Tanks over 6 ft 1. NOTE 7—The selection of the particular chopped-strand mat is dependent upon the performance characteristics required of the?

B Axial joint overlay widths shall be twice the width shown in table. This standard is subject to revision at any time by the responsible technical committee and must be reviewed every?

Special design consideration must be given to buckling astn tank wall and heads, the hold-down lug system, and top and bottom knuckle requirements. Only those constructions evaluated for design properties in As a custom manufacturer specializing in meeting the unique needs of our customers, our exposure to these different standards is much higher than for the manufacturer that produces a cookie cutter tank. Fluid level in the tank is an important consideration in the analysis.

This overlay shall be the equivalent of 7.

Overall thickness, mm h shear lengthmm A 14? Successive layers shall uniformly increase in width in that speci? The hoist wire should be connected to the top lifting lugs, and the tank should be raised carefully, using guide ropes to prevent sudden swinging.

NOTE 4—The addition of a thixotropic agent may reduce the resistance of many resin systems to certain corrosive chemical environments.