This standard is issued under the fixed designation D ; the number 1 This practice is under the jurisdiction of ASTM Committee D on Protective. ASTM D Standard Practice for Surface Cleaning Concrete for Coating. ASTM D (Plastic sheet test): Place plastic sheet on concrete stab for 24 hours. o ASTM-D Standard Practice for Surface Cleaning Concrete for.
|Published (Last):||2 February 2008|
|PDF File Size:||13.48 Mb|
|ePub File Size:||15.88 Mb|
|Price:||Free* [*Free Regsitration Required]|
Add to Alert PDF. When viewed without magnification, a White Metal Blast Cleaned surface should be free of any visible grease, oil, dust, dirt, mill scale, paint, rust, oxides, corrosion products, and other foreign matter. Surface must be free of laitance, concrete dust, dirt, form release agents, moisture curing membranes, loose cement, and hardeners. Brush Blasting or Sweep Blasting Includes dry blasting, water blasting, water blasting with abrasives, and vacuum blasting with abrasives.
Visible deposits of grease or oil must be asmt prior to power tool surface preparation by any method specified in SSPC-SP 1, Solvent Cleaning, or other agreed upon methods.
ASTM D – 05() Standard Practice for Surface Cleaning Concrete for Coating
Already Subscribed to this document. Spackle the drywall defects.
Maintenance painting will frequently not permit or require complete removal of all old coatings prior to repainting. Make sure all visible grease, oil, salts, and soluble welding residues have been removed prior to power tool cleaning by the methods outlined in SSPC-SP 1.
Need more than one copy? Make sure all visible grease, oil, salts, and soluble welding residues have been removed before hand tool cleaning by the methods outlined in SSPC-SP 1. Exterior composition board siding hardboard must be thoroughly cleaned and primed with an alkyd primer, whether factory primed or unprimed.
Thoroughly cleanse vinyl siding by scrubbing with a warm, soapy water solution. Standards Subsctiption may be the perfect solution. If these requirements are ignored, the lining can delaminate from the substrate or fail to cure properly. When viewed without magnification, a metallic surface prepared according to this specification should be free of any visible grease, oil, dust, dirt, mill scale, paint, rust, oxides, corrosion products, and other foreign matter.
ASTM D – 05 Standard Practice for Surface Cleaning Concrete for Coating
Wipe off the dust. The procedures below are intended to help assure optimum performance of the coating system and suitable asgm adhesion to concrete:. All of these steps were important to ensure the paint finish was smooth, uniform in color, and resilient.
Treat textured, soft, porous, or powdery plaster with a solution of 1 pint household vinegar to 1 gallon of water. The surface may be painted after 30 days if recommended procedures for applying stucco are followed, and normal drying conditions exist.
ASTM D4258 – 05(2017)
Here is a summary of some of the published x4258 with which installers and specifiers of corrosion protection linings should be familiar. Please first verify your email before subscribing to alerts.
This standard is not included wstm any packages. To test compatibility, apply a square foot area with the coating system, and allow concrete to dry one week before testing adhesion per ASTM D Plan accordingly to handle the runoff. Please first log in with a verified email before subscribing to alerts.
Rinse with clear water and allow to dry. To avoid premature lining failures resulting from improper surface preparation, lining specifiers, applicators, and inspectors need to be familiar with these industry standards for surface preparation and to adhere to their principles in practice. Allow to d42258 and cure thoroughly for at least 30 days prior to painting.
Thorough washing with an abrasive cleanser will clean and dull in one operation, or, wash thoroughly and dull by sanding. When viewed without magnification, a Brush-Off Blast Cleaned surface should be free of any visible grease, oil, dust, dirt, loose mill scale, loose paint, and loose d42588. For f4258 surfaces, spackle with exterior grade compounds.
All nail heads must be set and spackled. Small residues of rust and paint may be left in the lower portions of pits if the original surface is pitted.