ASTM F2054 PDF

ASTM Standards. ASTM F ASTM F – Standard Test Method for Burst Testing of Flexible Package Seals Using Internal Air Pressurization Within. Consult Labthink Instruments Co., Ltd.’s High Pressure Leak Tester for Package ASTM F, ASTM F brochure on DirectIndustry. Page: 1/4. More help in interpreting the results can be found in ASTM F Inflation Seal Strength Testing (ASTM F and F), including burst, creep and creep-to-.

Author: Gamuro Zurisar
Country: Nicaragua
Language: English (Spanish)
Genre: Marketing
Published (Last): 24 July 2016
Pages: 500
PDF File Size: 17.67 Mb
ePub File Size: 10.20 Mb
ISBN: 327-9-33218-296-1
Downloads: 25527
Price: Free* [*Free Regsitration Required]
Uploader: Vobar

MFY leak detector for our pouch packaging.

ASTM F | Rycobel

Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as f22054 of the standard. Reference Appendix X3 for further information regarding calculation of stress factors and structural design aastm. FT-F1 Fogging tester to to test for fogging on upholstery material and time frame for testing.

This test method also cannot provide an evaluation of overall package integrity or the burst strength of areas of the package that contact the surface of the restraining plates used. This allows the test to have a higher probability of astk the weakest area of the seal and provide a measurement of the pressure required to “burst” open the package.

This test method cannot provide a measure of package seal uniformity.

ASTM F2054/F2054M – 13

Historical Version s – view previous versions of standard. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Tensile Tester for both compression and tensile, with loads typically N.

MFY Leak Tester is used to look for pin holes in bags that hold calibration solutions for medical instruments. Under unrestrained conditions the stress on the package is highest at the middle of the pouch where it inflates to the packages maximum diameter; therefore, Test Methods F may not reliably detect the weakest area of the seal. See Appendix X2 for further information. Oxygen Permeability Tester to test containers.

  FOROUGH FARROKHZAD POEMS PDF

Product List | RDM Test Equipment | Assured Quality Testing Solutions

An indicator of the minimum burst strength may be of importance to the package manufacturer and end user in ensuring adequate package integrity. Seal Strength system to test 3 sides seal bags. Particular caution is advised where users of this procedure may be required to design and fabricate restraining f20054 fixtures.

By placing the package within restraining plates during pressurization, the dimensional stability of the package is maintained in a manner that results in stresses applied more uniformly along the perimeter of the package, where seals are normally placed. By placing the package within restraining plates during pressurization, the dimensional stability of the package is maintained in a manner that results in stresses applied more uniformly along the perimeter of the package, where seals are normally placed.

Specifications Test Range Contact: Particular caution is advised where users of this procedure may be required to design and fabricate restraining plate fixtures. Test Methods F describes methods of burst testing that do not include the use of restraining plates and are suitable to determine a packages general ability to withstand pressurization stresses. Under Test Methods F the stresses are not distributed uniformly to all areas of the package seal.

Thickness micron testing equipment with Resolution 0. Reference Appendix X3 for further information regarding calculation of stress factors and structural design considerations. See Appendix X4 for information. Pressure differentials may occur during such processes as sterilization and transportation. This test method should be combined with other methods of evaluating overall package integrity, uniformity of the package seal, or opening functionality, if so required. This test method provides an indicator of the burst strength of a package, where the burst will normally occur in one or more areas of the seal.

This standard does not purport to address all of the safety concerns, if any, associated with its use. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.

Link to Active This link will always route to the current Active version of the standard. Test Methods F describes methods of burst testing that do not include the use of restraining plates and are suitable to determine a packages general ability to withstand pressurization stresses.

  BARBRI MPRE PDF

Labthink provides COF Tester for coef. In particular it is intended as applicable to packages with seals that have a peelable seal feature peeled open by end user to remove contents of package. Under Test Methods F the stresses are not distributed uniformly to all areas of the package seal.

ASTM F2054

Three Tests in one instrument High Pressure Leak tester With various accessories for tests of different packages Applications: See Appendix X4 for information.

Active view current version of standard. Vacuum Leak Tester for bottles for food, chemical and pharmaceutical applications. Under unrestrained conditions the stress on the package is highest qstm the middle of the pouch where it inflates to the packages maximum diameter; therefore, Test Methods F may not reliably detect the weakest area of the seal. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

The Online Industrial Exhibition.

Labthink RT rub tester to test on flexo printing. COF Inclined Plane Tester Measure the static coefficient of friction of various materials aetm a variable inclined plane and a sliding block.

Link to Active This link will always route to the current Active version of the standard. Flexible packages, aseptic packages, various plastic pilfer-proof closures, flexible tubes, caps and other materials. In particular it is intended awtm applicable to packages with seals that have a peelable seal feature peeled open by end user to remove contents of package.

Typical parameters can include, but are not limited to the package size, material, type and configuration of seal, rate of air flow into the package, pressure detection sensing mechanism and sensitivity machine ast to pressure dropposition of test article, rigidity of restraining plates, and distance between restraining plates.