and wiring for Japanese specification FX1N PLC main units. This manual covers basic hardware details for the FX1N Series Programmable Logic Controller. FX1N Hardware Manual – 三菱可编程控制器FX1N型PLC硬件手册. User’s Manual. (Data Communication). FX1S/FX1N/FX2N(C)/FX3U. Interface Modules. INDUSTRIAL AUTOMATION. MITSUBISHI ELECTRIC. MITSUBISHI.
|Published (Last):||5 April 2018|
|PDF File Size:||13.74 Mb|
|ePub File Size:||18.79 Mb|
|Price:||Free* [*Free Regsitration Required]|
During this testing stage take extreme care not to touch any live or hazardous parts. Take special care not to allow debris to fall inside the unit during installation e.
Mitsubishi FX1N-24MT-DSS Manuals
This includes being completely familiar with all associated documentation for the said product. AC, World spec, CE registered. Circuit protector or Fuse? Units should not be installed in areas subject to the following conditions: Please refer to the table below.
If resistance Rp is less than the stated value, then add Rb. Grounding is recommended but if a proper ground cannot be provided, the PLC will still operate correctly without being grounded.
Check the previously down loaded program works haddware. A standard input X0 to X17 defined by the system parameters.
This manual provides information for the installation and use of the FX1N. Only one board can be used at any one time, do not try to stack multiple boards.
FX1N Hardware Manual_图文_百度文库
This manual contains text, diagrams and explanations which will guide the reader in the correct installation and operation of the FX 1N Series Programmable Controllers. E M3 screw to secure top cover. Check D for program scan time, units 0.
All layouts are diagrammatic and are only intended to aid the creation of wiring diagrams. Note that the ground cable must not be connected to the same ground as the power circuits.
Mitsubishi FX1NMT-DSS Manuals
Please note that the over current induced by in-rush greatly reduces the relay contacts service life. C M3 screw to secure top cover. Remove the base unit top cover. All examples and diagrams shown in this manual are intended only as an aid to understanding the text, not to guarantee operation. Do not manjal this terminal Fuse Surge absorbing Diode.
These engineers should also be trained in the use and maintenance of the completed product. Input circuit power supply?
Note all counters are latched Remarks C0 to C15 Type: Mitsubishi Electric will accept no responsibility for actual use of the product based on these illustrative examples. Always ensure that mounted units and blocks are kept as far as possible from high-voltage cables, high-voltage equipment and power equipment. Do not remove this screw. The definition of such a person or persons is as follows; a Any engineer who is responsible for the planning, design and construction of automatic equipment using the product associated with this manual should be of a competent nature, trained and qualified to the local and national standards required to fulfill that role.
Ground resistance must be less than ? Software warning 4 Indicates special care must be taken when using this element of software.
Associated Manuals The following manuals are recomended as esential reference material for the correct operation of a FX1N series Programmable controller.
If during the installation of these product or associated products concern is felt, please contact a professional electrician who is trained to the local and national standards applicable to the installation site. Remotely from a personal computer or other programming peripheral. Never mount them to the floor or ceiling of an enclosure. See equation 2 for Rb calculation. Circuit protector or fuse? The following instructions are also not suitable. Low voltage cables should be reliably separated or insulated with regard to high voltage cabling.
The enclosure should be selected and installed in accordance to the local and national standards.
Mitsubishi FX1N-24MT-ESS/UL Manuals
Check the power LED is lit. Check the output LEDs for ffx1n. Under no circumstances will Mitsubishi Electric be liable or responsible for any consequential damage that may arise as a result of the installation or use of this equipment.