The regulatory requirements in maritime and offshore applications are defined by the standards IEC for maritime navigation and radio communication. Our antennas meet several international standards for marine equipment, such as IEC , GOST, IACS E10 and RMRS. Some of the tests described in the. Dedicated to safe ships and clean seas, IACS makes a unique contribution to maritime safety and regulation through technical support, compliance verification .

Author: Jull Nirg
Country: Liberia
Language: English (Spanish)
Genre: Automotive
Published (Last): 16 July 2013
Pages: 219
PDF File Size: 15.22 Mb
ePub File Size: 10.82 Mb
ISBN: 550-5-74875-576-4
Downloads: 26460
Price: Free* [*Free Regsitration Required]
Uploader: Bram

Recent revisions and changes have been underlined for easy reference.

Interval between each application: External surface area of the tank for determining sizing of pressure relief valve paragraph 8. For severe vibration conditions such as, e.

UR E10 Rev6 CLN

Texts of the IACS Unified Requirements and Unified Interpretations are made available on this page for the period of one year following the iacd of adoption. Damp heat IEC Publication test Db – measurement of insulation resistance before test; – equipment operating during the complete first cycle and switched off during second cycle except for functional test; – functional test during the first 2 hours of the first cycle at the iac temperature and during the last 2 hours of the second cycle at the test temperature; – recovery at standard atmosphere conditions; – ias resistance measurements and performance test.

The period of testing in each position should be sufficient to fully evaluate the behaviour of the equipment. The test in each direction is to be carried out for not less than 15 minutes.


For equipment installed on the bridge and deck zone, the test levels shall be increased to 10V rms for spot frequencies in accordance with IEC at 2, 3, 4, 6. During the test, degradation or ixcs of function or performance which is self recoverable is however allowed but no change of actual operating state or stored data is allowed.

These inclination tests are normally not required for equipment with no moving parts.

Appropriate location of premixed engines using fuel gas mixed with air before the turbocharger. According to level 2 severity standard Single pulse time: Equipment to be mounted in consoles, housing etc. Special consideration within the risk assessment of closed or semi-enclosed bunkering stations.

Sweep over a restricted frequency range between 0. Pipes and Pressure Vessels S: However, equivalent testing procedure may be accepted by the individual Society provided that the Unified Requirements stated in the other columns are fulfilled. Equipment is to be tested in its normal position if otherwise not specified iwcs the test specification.

IACS UR E10_图文_百度文库

Approval of consumables for welding normal and higher strength hull structural steels. Control and maintenance of pressure and temperature of liquefied gas fuel tanks after the activation of the safety system. Selective disconnection or shutdown and equipment operable after an emergency shutdown. The outlines of technical resolutions adopted by IACS are available at the links shown below.

Passenger Submersible Craft SC: The Equipment Under Test shall continue to operate as intended during and after the test.


Electrical and electronic equipment on board ships, required neither by classification rules nor by International Conventions, liable to cause eletromagnetic disturbance shall be of type which fulfill the test requirements of test specification items 19 and Mooring, Anchoring and Towing C: The EUT shall continue to operate as intended after the tests. Shipboard fittings and supporting hull structures associated with towing and mooring on conventional ships.

More severe conditions may exist for example on exhaust manifolds of diesel engines especially for medium and high speed engines. No degradation of performance or loss of function is allowed as defined in the technical specification published by the manufacturer.

Salt mist test is to be carried out for equipment installed in weather exposed areas. Relevant tests are as listed in the Table. Mobile Offshore Drilling Units E: Using the directions defined in a to d above, the equipment is to be rolled to an angle of Notes to Test No.

Materials and Welding Z: Strength of Ships W: Critical iace is a frequency at which the equipment being tested may exhibit: Test criteria based upon application. Electrostatic discharge IEC Contact discharge: Protection against cryogenic leakage and control of hazardous zones in fuel preparation rooms on open deck.