IBANEZ S520EX MANUAL PDF

The SEX is an S series solid body electric guitar model introduced by Ibanez in It was initially produced in Korea and then later in Indonesia. There’s no way a guy who does a couple guitar setups every day of the year would do a better than someone will with instructions from the. For over 18 years, Ibanez RG guitars with Edge double locking sys- tems have been SEX MOF. • 3pc Wizard II Manually Adjustable Zero. Point System.

Author: Tokus Zushicage
Country: Luxembourg
Language: English (Spanish)
Genre: History
Published (Last): 2 April 2011
Pages: 496
PDF File Size: 18.6 Mb
ePub File Size: 8.68 Mb
ISBN: 423-4-64469-223-8
Downloads: 36438
Price: Free* [*Free Regsitration Required]
Uploader: Visida

Retune the guitar to the proper pitch and check the angle. The height adjustment of the tremolo can be set by using the two 3mm adjustment screws on either side of the tremolo unit. Before adjusting the intonation, first determine the direction that the saddle needs to be moved.

| Wiring Diagrams

Wind the string around the tuning machine and tune to pitch. To allow the arm to swing freely. Loosen the pressure pad lock screws on the top lock with a 3mm allen wrench. To remove the tremolo arm, firmly s520xe the arm at the break over point bend and pull up until the arm is released.

Solid Body Electric Guitars. Play the harmonic at the 12th fret, compare it to the fretted noteat the 12th fret, these notes should read the same on the tuner. Remove the tremolo cavity cover plate from the back of the body.

  DAVE BRUBECK BLUE RONDO ALA TURK PDF

Adjusting the intonation is performed by moving the individual string saddles forward or backward. Cut off the ball end of the new string above the string winding and insert the end of the string in between the main saddle and the string holder block.

Make sure the truss rod is properly adjusted before adjusting the action. If this happens, replace the arm bushings with new ones. Over adjustment can result in damage to the instrument and will no be covered under warranty. To further reduce the torque, remove both bushings.

To adjust the string height of the saddles use a 1. If the ibanwz fret harmonic pitch is lower than the fretted note, the saddle needs to be moved back. Tighten the pressure pad screws. Raise or lower the tremolo to the desired string height using a 4mm allen wrench. When the guitar is properly adjusted, tighten the top lock pressure pad screws.

Loosen the string stopper bolt by using a 3mm allen wrench, and remove the string from the saddle. Cut off the ball end of the new string above the string winding and insert the end of the string in between the main saddle and the String holder block. The truss rod is adjustable at the headstock using as allen wrench or an adjustment wrench. Play the harmonic at the 12th fret, compare it to the fretted note at the 12th fret, these notes should read the same on the tuner.

Always loosen the Stud lock screws counter clockwise with a 1. To check the intonation: Loosen the heigth adjustment screw 5 on both sides of the bridge using ihanez 2 Phillips 2.

  KODAK SV710 PDF

Wiring Diagrams

On the bass plate there are two holes for each saddle lock down screw. Loosen the pressure pad screws on the top lock with a 3mm allen wrench and loosen the string to be adjusted. Adjust the saddle forward or backward to the proper position and tighten the saddle lock down screw.

Only loosen the screw enough to move the saddle. Tighten the String stopper Screw. Adjusting the String Height. Loosen the heigth adjustment screw 5 on both sides of the bridge using a 2 Phillips. The rotation torque of the arm can be adjusted by changing the number of bushings on the arm. For ease in retuning, it is recommended that one string at a time be changed and tuned.

| Help & How To

Use an electronic tuner and tune the guitar to a standard pitch. If lower than standard settings are desired, this can often result in”buzz” or “rattle” of the strings.

Both bushings should be completely hidden. Occasionally, there are times when the neck may need adjustment. Raise or lower the tremolo to the desired string height using a manuap allen wrench.