KEMA 08 ATEX IECEx KEM Features. □ Wide temperature range . □ PLEXO connection system, cold-applied connection and shrinkable tubing. EU-Type Examination Certificate Number: KEMA 98ATEX X are recorded in confidential test report number NL/KEM/ExTR/ KEMA 05ATEX X. PTB 02 ATEX X. Electrical KEMA 08ATEX SEV 10 ATEX SEV 10 ATEX SEV 10 ATEX SEV 10 ATEX.

Author: Zunris Faekus
Country: Niger
Language: English (Spanish)
Genre: Sex
Published (Last): 11 April 2016
Pages: 149
PDF File Size: 13.46 Mb
ePub File Size: 15.44 Mb
ISBN: 768-6-23842-266-1
Downloads: 99903
Price: Free* [*Free Regsitration Required]
Uploader: Tezragore

Stainless steel System The individual inputs are assigned and configured either by means of the Atdx ProcessDesigner software or by the touch panel.

Please insert correct code. AC 70 to V Contact loadability direct switching: Mounting plates and brackets in stainless steel After the preparation of the heating tape, insulation tubes are shrunk over the conductors and the twisted protective braiding and wire end sleeves are placed. The heating circuit end is also closed with shrinkable tubes. The benefit to the customer is obvious.

A high resistance results in a low heating output. Nylon cable ties The programming interface allows the device parameters to be read out with a code key and transferred to other controllers.


Connecting the GW32 gateway and PA00 touchpanel allows a transfer not only of the setpoint and actual values but also of all alarms into a higher ranking control. To use this website, you must agree to our Privacy Policyincluding cookie policy. Using the programming interface, the device parameters can be read out with a programming key and transmitted to other devices.


This characteristic is used for this type of resistance thermometers to get an image of the temperature. If desired, the autotuning function will automatically determine the optimum PID adjusting parameters for the control path. Single-core mineral-insulated heating cable, laser welded, pre-assembled, Ex and M The EKL system can be perfectly adjusted to the customer specific requirements.

The power output controller works in interference free full wave control mode by means of a semiconductor relay. This self-limiting property prevents overheating even when the tapes are crossed.

All that is needed to assemble a heating circuit is a knife and diagonal cutter. This dispenses with the time-consuming work of exposing the two conductors, the laborious splicing and twisting of the protective braiding and then connecting to a terminal.

The monitoring length can be divided into 50 zones per measuring channel.

All details about electrical explosion protection mentioned in this certificate are for information only. Basically, the heating tape is connected to terminals in an enclosure that has the protection type “increased safety”. N are insulated with silicone glue and a silicone hose.


See System Description for Installation Instructions. Each leakage is detected with metre accuracy and reported directly in atdx building surveillance. The inner one of the two jackets is thermally fused to the heating element bonded jacket. Terminals Terminal screws 2 x 1. PLC programming skills are not necessary. The terminal leads integrated on both sides make the device a readyto-connect heater.


Technical data | Heating Technology

An output module provides floating contacts to emit alarms. The DTL will also interrupt the switch contact in the event of a sensor open or short circuit.

The heatings or heating circuits can be installed both in media-protected and also in hazardous potentially explosive areas. Circuit diagram Accuracy of reference junction with thermocouple measurements 0.

Enclosure material Aluminium, black aetx Connections for temperature sensors, current and voltage transducers are located on the back of the device.

IP 53 Type EKL premium Heating cable, Heat conductor EKL premium flexible single-core plastic-insulated heating cable 2. Places of use include switch and control cabinets, transmitter protective boxes, measuring equipment, analytical cabinets for sample preparation etc.

Fixing straps Connection cables Adhesive tapes The temperature class can be specified: Function The load and residual current monitor constantly checks the entire heating system and ensures that the heating cables and temperature sensors always function reliably.